INSTALLATIONS BY DC, LLC.

SECTION 12493 [12 24 00]

E1 MOTORIZED WINDOW SHADES

PART 1 GENERAL

1.1SECTION INCLUDES

1.A.Motorized, roll-up fabric interior window shades including motor operator, controls, and mounting hardware.

1.2RELATED SECTIONS

2.A.Section 06100 [06 10 00] – Rough Carpentry: Blocking for support of window shade hardware.

2.B.Section 07900 [07 90 00] – Joint Sealers: Sealants for perimeter of shade system.

2.C.Section 09260 [09 21 23] – Gypsum Board Assemblies: Suspended gypsum board ceilings to contain recessed window shade pockets.

2.D.Section 09510 [09 51 23] – Acoustical Tile Ceilings: Suspended acoustical panel ceilings to contain recessed window shade pockets.

2.E.Section 11132 [11 52 13] – Motorized Projection Screens: Motorized projection screens to be interfaced with shade controls.

2.F.Section 11132 [11 52 13] – Motorized Projector Lifts: Motorized projector lifts and mounts to be interfaced with shade controls.

2.G.Division 16 [26] – Electrical: Electrical supply, conduit, and wiring for motorized window shades.

1.3REFERENCES

3.A.NFPA 70 – National Electrical Code.

3.B.NFPA 701-99 – Fire Tests for Flame-Resistant Textiles and Films.

3.C.GREENGUARD Environmental Institute Gold.

3.D.US Green Building Council.

3.E.ANSI/WCMA A100.1-2018

1.4SUBMITTALS

4.A.Submit under provisions of Section 01330 [01 33 26] – Submittal Procedures:

4.B.Product Data: Manufacturer’s data sheets on each product specified, including:

4.B.1.Preparation instructions and recommendations.

4.B.2.Installation and maintenance instructions.

4.B.3.Styles, material descriptions, dimensions of individual components, profiles, features, finishes and operating instructions.

4.B.4.Storage and handling requirements and recommendations.

4.B.5.Mounting details and installation methods.

4.B.6.Typical wiring diagrams including integration of motor controllers with building management system, audiovisual and lighting control systems as applicable.

4.C.Shop Drawings: Plans, elevations, sections, product details, installation details, operational clearances, wiring diagrams and relationship to adjacent work.

4.D.LEED Submittals: Provide documentation of how the requirements of Credit will be met.

4.E.Window Treatment Schedule: For all roller shades. Use same room designations as indicated on the Drawings, field verified window dimensions, quantities, type of shade, controls, fabric, and color, and include opening sizes and key to typical mounting details.

4.F.Selection Samples: For each finish product specified, two complete sets of shade cloth options and aluminum finish color samples representing manufacturer’s full range of available colors and patterns.

4.G.Verification Samples: For each finish product specified, two complete sets of shade components, unassembled, demonstrating compliance with specified requirements. Shade fabric sample and aluminum finish sample as selected, representing actual product, color, and patterns. Mark face of material to indicate interior faces.

4.H.Maintenance Data: Methods for maintaining roller shades, precautions regarding cleaning materials and methods, instructions for operating hardware and controls.

4.I.Manufacturer’s Certificates: Certify products meet or exceed specified requirements.

1.5QUALITY ASSURANCE

5.A.Manufacturer Qualifications: Obtain roller shades through one source from a single manufacturer with a minimum of twenty years’ experience in manufacturing products comparable to those specified in this section.

5.B.NFPA Flame-Test: Passes NFPA 701. Materials tested shall be identical to products proposed for use.

5.C.Shading system shall be UL listed. Provide documentation and proper labeling.

5.D.Mock-Up: Provide a mock-up of one of each type roller shade assembly specified for evaluation of mounting, appearance and accessories.

5.D.1.Locate mock-up in window(s) designated by Architect.

5.D.2.Do not proceed with remaining work until mock-up is accepted by Architect.

1.6DELIVERY, STORAGE, AND HANDLING

6.A.Do not deliver window shades until building is enclosed and construction within spaces where shades will be installed is substantially complete.

6.B.Deliver products in manufacturer’s original, unopened, undamaged containers with labels intact.

6.C.Label containers and shades according to Window Shade Schedule.

6.D.Store products in manufacturer’s unopened packaging until ready for installation.

1.7SEQUENCING

7.A.Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress.

7.B.Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.8PROJECT CONDITIONS

8.A.Install roller shades after finish work and ambient temperature, humidity and ventilation conditions are maintained at levels recommended for project upon completion.

1.9WARRANTY

9.A.Hardware: standard five-year limited warranty.

9.B.Motors and Controls: standard five-year limited warranty.

PART 2 PRODUCTS

2.1MANUFACTURERS

1.A.Acceptable Manufacturer: Installations by DC, LLC. 5101 Chase Avenue, Downers Grove, IL 60515. Office Phone 630-323-2381, dcinstallations.com

1.B.Substitutions: Not permitted.

1.C.Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 MOTORIZED WINDOW SHADES

2.A.Type: UL listed, motorized, vertical roll-up, fabric window shade with motors, controls, mounting brackets, and other components necessary for complete installation; Motorized AC as manufactured by Installations by DC, LLC.

2.A.1.Mounting brackets.

2.A.2.Endcaps and fascia.

2.A.3.Endcaps and pocket headbox.

2.A.4.Endcaps and ceiling/wall headbox.

2.A.5.Ceiling pocket.

2.B.Shade Motor and Control System

2.B.1.Motorized AC.

2.B.1.a.120V AC Intelligent Technology motor with built-in low voltage controller with 3-wire pig tail and data cable. No external motor controls are required. Available with optional three prong plug. Tubular motor concealed inside each shade roller tube.

2.B.1.b.Quiet 120V AC Intelligent Technology Motor – 120V AC quiet motor with built-in low voltage controller with 3-wire pig tail and data cable. Motor operates at 38 dBA measured 3 feet from the motor. Makes no audible clicks when motor stops or starts. Available with optional three prong plug. Tubular motor concealed inside each shade roller tube.

2.B.1.c.Individual Control, Group Control & Individual and Group Control:

2.B.1.c.1)6 Button RS 485 switch- for up/stop/down control. 3 presets

2.B.1.c.2)8 button RS 485 switch- for up/stop/down. 5 presets.

2.B.1.c.3)Somfy Digital Network. SDN system of window shades with intelligent motors linked to an IP interface box and other input devices for automated glare control.

(2.B.1.c.3.a)Bus Distribution

(2.B.1.c.3.a.1)Data Hub for 485 Motor

(2.B.1.c.3.a.2)5-Way RJ45 Splitter

(2.B.1.c.3.b)Building Controllers

(2.B.1.c.3.b.1)SDN Data Panel

(2.B.1.c.3.c)User Interfaces

(2.B.1.c.3.c.1)Somfy Connect BMS Interface

(2.B.1.c.3.c.2)Somfy Connect LTI

(2.B.1.c.3.c.3)Z Wave Digital Motor Interface (ZDMI)

(2.B.1.c.3.c.4)Zigbee to RS485 (ZBDMI)

(2.B.1.c.3.c.5)RTS Receiver for 485

(2.B.1.c.3.c.6)SDN 6 button wall switch (Preprogrammed for master control)

(2.B.1.c.3.c.7)SDN 8 button wall switch

(2.B.1.c.3.c.8)Somfy Connect UAI Plus

(2.B.1.c.3.d)Accessories

(2.B.1.c.3.d.1)Bus Power Supply, 24V, 1A

(2.B.1.c.3.d.2)SDN Power over Ethernet Gateway

(2.B.1.c.3.e)Sensors

(2.B.1.c.3.e.1)Animeo IP Outside Sensor Box

(2.B.1.c.3.e.2)Animeo IP Inside Sensor Box

(2.B.1.c.3.e.3)Animeo IP Compact Sensor

(2.B.1.c.3.e.4)Brightness Sensor

(2.B.1.c.3.f)Animeo Building Controllers

(2.B.1.c.3.f.1)Animeo IP Building Controller

(2.B.1.c.3.f.2)Animeo IP Sub Controller

(2.B.1.c.3.g)Animeo User Interfaces

(2.B.1.c.3.g.1)Animeo IP RTS Receiver

(2.B.1.c.3.g.2)Animeo IP 6 button wall switch

(2.B.1.c.3.g.3)Animeo IP 8 button wall switch

2.C.Configuration:

2.C.1.Single Roller.

2.C.1.a.Mounting.

2.C.1.a.1)Endcaps: Stamped steel with universal design suitable for mounting to ceiling, wall, and jamb. Provide size compatible with roller size. Endcap covers to match fascia/headbox finish.

2.C.1.a.2)Brackets: 1/8-inch-thick stamped steel, black powder coat, idler height adjuster, field adjustable to wall or ceiling mount.

(2.C.1.a.2.a)Mounted to ceiling.

(2.C.1.a.2.b)Mounted to wall.

(2.C.1.a.2.c)Mounted to jamb.

2.C.1.a.3)Fascia: L shaped aluminum extrusion to conceal shade roller and hardware.

(2.C.1.a.3.a)Attachment: Snaps onto end caps without requiring exposed fasteners of any kind. Fascia can be mounted continuously across two or more shade bands.

(2.C.1.a.3.b)Finish: Clear anodized.

(2.C.1.a.3.c)Finish: Black powder coat.

(2.C.1.a.3.d)Finish: White powder coat.

(2.C.1.a.3.e)Finish: Ivory powder coat.

(2.C.1.a.3.f)Finish: Bronze powder coat.

(2.C.1.a.3.g)Finish: Custom powder coat as selected by the Architect.

(2.C.1.a.3.h)Finish: Fabric-Wrapped.

2.C.1.a.4)Headbox Ceiling/Wall Style: Aluminum fabrication with removable closure, endcaps, and back and top cover piece:

(2.C.1.a.4.a)Finish: Clear anodized.

(2.C.1.a.4.b)Finish: Black powder coat.

(2.C.1.a.4.c)Finish: White powder coat.

(2.C.1.a.4.d)Finish: Ivory powder coat.

(2.C.1.a.4.e)Finish: Bronze powder coat.

(2.C.1.a.4.f)Finish: Custom powder coat as selected by the Architect.

2.C.1.a.5)Headbox, Pocket Style: Aluminum fabrication with removable closure, endcaps, and U-shaped pocket:

(2.C.1.a.5.a)Finish: Clear anodized.

(2.C.1.a.5.b)Finish: Black powder coat.

(2.C.1.a.5.c)Finish: White powder coat.

(2.C.1.a.5.d)Finish: Ivory powder coat.

(2.C.1.a.5.e)Finish: Bronze powder coat.

(2.C.1.a.5.f)Finish: Custom powder coat as selected by the Architect.

2.C.1.a.6)Type D Shade pocket: Rectangular pocket with ceiling tile lip designed for recessed ceiling installation of window shades.

(2.C.1.a.6.a)Material: Extruded aluminum alloy with white epoxy paint finish.

(2.C.1.a.6.b)Size: 5 inches (127 mm) by 5-5/8 inches (137 mm) high.

(2.C.1.a.6.c)Closure Panel:

1-1/2 (38 mm) closure dimension.

3 inch (78 mm)

(2.C.1.a.6.d)Pocket Endcap Kit: Endcaps with 7/8-inch (22 mm) lip for support of acoustical ceiling panel.

(2.C.1.a.6.e)Corners: Welded one-piece aluminum sections connecting to and matching pockets to allow continuous shade recess at ceiling corners.

(2.C.1.a.6.f)Pocket ends: Welded one-piece aluminum sections connecting to and matching pockets.

2.C.1.a.7)Wall Clip with Closure panel: For site constructed ceiling recesses, provide removable closure panel to minimize slot for shade passage but allowing access to shade for maintenance.

(2.C.1.a.7.a)Material: Aluminum alloy with white epoxy paint finish.

(2.C.1.a.7.b)Tile Lip: Provide wall clip with 7/8-inch tile lip (22 mm).

(2.C.1.a.7.c)Closure width: 1-1/2 inches (38 mm).

(2.C.1.a.7.d)Closure width: 3 inches (75 mm).

(2.C.1.a.7.e)Closure Width: 5 inches (127 mm).

(2.C.1.a.7.f)Provide continuous wall clip, 1-3/4 (44 mm) by 3/16 inch (5 mm), for snap-in attachment of closure panel without fasteners.

2.D.Aluminum Light Gap Reduction Channels

2.D.1.L Angle – 3/4 inch by 1 inch (19 mm by 25 mm).

2.D.2.L Angle – 1 inch by 2-3/4 inches (25 mm by 70 mm).

2.D.3.U Channel – 1 inch by 2-1/2 inches (25 mm by 64 mm).

2.D.4.H Channel – 1 inch (25 mm) by 5 inches (127 mm).

2.E.Vinyl Light Gap Reduction Channels

2.E.1.L Angle – 1-1/2 inches 3/4 inches (38 mm by 19 mm).

2.F.Interior cable guide kit

2.F.1.Interior cable hem bar finial.

2.F.2.Cable mount.

2.F.3.Cable.

2.F.4.Tension Stop.

2.G.Shade slat:

2.G.1.Closed pocket elliptical slat: 1 inch (25 mm) aluminum elliptical slat inside of a 1-5/8-inch (41 mm) pocket with heat sealed ends.

2.G.2.Open pocket elliptical slat: 1 inch (25mm) aluminum elliptical slat with plastic ends inside of a 1-5/8-inch (41 mm) pocket.

2.G.3.Flat exposed hem bar: Small: 7/8-inch x 5/16-inch (22 mm x 8 mm) and Large 1-1/2-inch x 5/16-inch (38 mm x 8 mm) aluminum rectangular hem bar with plastic end caps.

2.G.4.Round exposed hem bar: Small 5/8-inch (16 mm) and Large 13/16-inch (21 mm) aluminum with plastic end caps.

2.H.Roller: Fabricated from extruded aluminum or steel. Wall thickness and material selected by manufacturer to accommodate shade size. Provide with roller idler assembly of molded nylon and zinc-plated steel pin. Sliding pin to allow easy installation and removal of roller. Fabric connected to the roller tube with LSE (low surface energy) double sided adhesive specifically developed to attach coated textiles to metal. Adhesive attachment to eliminate horizontal impressions in fabric.

2.I.Coupling system: Couplings to join motorized shade rollers to allow operation by single motor. FlexShade Coupling System as manufactured by Draper, Inc. Provide endcaps to receive couplers and support multiple shades. Coupling system must be capable of up to 30-degree angles.

2.3FABRIC

3.A.Room Darkening Fabrics

3.A.1.SunBloc Series SB9000: Close woven fiberglass base textile with sun-resistant vinyl film bonded to each side, opaque with minimum tensile strength of 190 pounds for warp and 180 pounds for fill. Fire rating: NFPA 701 1006-Test 1, California U.S. Title 19. Environmental Benefits: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. REACH and RoHS compliant – Lead Free. Bacterial and fungal resistance: ASTM E2180, ASTM G21. Washable and stain resistant. Same color both sides. Opaque, .015 inches thick, 12 oz/square yard.

3.A.2.SunBloc Series SB9100: Close woven fiberglass base textile with sun-resistant vinyl film bonded to each side, opaque with minimum tensile strength of 190 pounds for warp and 180 pounds for fill. Fire rating: NFPA 701 1006-Test 1, California U.S. Title 19. Environmental Benefits: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. REACH and RoHS compliant – Lead Free. Bacterial and fungal resistance: ASTM E2180, ASTM G21. Washable and stain resistant. White exterior in all colors. Opaque, .013 inches thick, 12 oz/square yard.

3.A.3.Flocké® by Mermet®: Opaque, PVC-free fiberglass textile with acrylic flocked backing. Antistatic treated. Fire rating: NFPA 701-10 TM#1, California U.S. Title 19, CAN/ULC-S109-03 Small & Large Flame Test. Environmental Benefits: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. RoHS compliant – lead free. Bacterial and fungal resistance: ASTM E2180, ASTM G21. Draper shades made with this fabric are GreenSpec® listed. Opaque, .020 inches thick, 15.93 oz/square yard.

3.A.4.SheerWeave® Series SW7000 Blackout by Phifer®: PVC-free polyester with acrylic foamed backing. Fire rating: California U.S. Title 19 (small scale), BS 5867 Part 2 Type B Performance, IBC Section 803.1.1 (Class A Rating), NFPA 101 (Class A Rating), NFPA 701 TM#1 (small scale), CAN/ULC-S 109 (large and small scale), CAN/CGSB2-4. 162-M80. Bacterial and fungal resistance: ASTM G21, AATCC 174-1998 Part II and III. Environmental certification: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. Safe use: RoHS/Directive 2002/95/EC, US Consumer Product Safety Commission Section 101 and ANSI/WCMA A 100.1-2007 for lead content. Draper shades made with this fabric are GreenSpec® listed. Opaque, .030 inches thick, 13.92 oz/square yard.

3.A.5.SheerWeave® Series SW7100 Blackout by Phifer®: PVC-coated Fiberglass laminated with a 2-ply PVC film. Fire rating: NFPA 701 TM#1 (small scale), NFPA 701 TM#2 (large scale), BS 5867 Part 2 Type B Performance, CAN/ULC-S 109 (large and small scale), NFPA 101 (Class B Rating), IBC Section 803.1.1 (Class B Rating). Bacterial and fungal resistance: ASTM E 2180, ASTM G21, ASTM G22, AATCC30 Part 3, ASTM D 3273, GREENGUARD® Mold and Bacteria Standard ASTM 6329; Style 2000 face includes Microban® antimicrobial additives. Environmental certification: Certified to GREENGUARD and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. Safe Use: RoHS/Directive 2002/95/EC, US Consumer Product Safety Commission Section 101, ANSI/WCMA A 100.1-2007 for lead content and REACH (EC 1907/2006) compliant. Opaque, .025 inches thick, 21.6 oz/square yard, opaque.

3.A.6.SheerWeave® Series SW7400 by Phifer®: PVC-free polyester with acrylic foamed backing. Fire rating: California U.S. Title 19 (small scale), CAN/ULC-S 109 (large and small scale), CAN/CGSB 2-4. 162-M80, NFPA 701 TM#1 (small scale), NFPA 701 TM#2 (large scale). Bacterial and Fungal Resistance: ASTM G21-96, AATCC 174-1998 Part II and III. Environmental Certification: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. Safe Use: RoHS/Directive 2002/95/EC, ANSI/WCMA A 100.1-2007 for lead content, US Consumer Product Safety Commission Section 101. UV Protection: Seal of Approval by the Melanoma International Foundation (MIF) for effectiveness in preventing sun damage to the skin or eyes. Opaque, .029 inches thick, 12.53 oz/square yard.

3.A.7.SheerWeave® Series SW7500 by Phifer®: PVC-free polyester with an acrylic coating. Fire rating: California U.S. Title 19 (small scale), NFPA 101 (Class A Rating), NFPA 701 TM#1 (small scale), BS 5867 Part 2 Type B Performance, CAN/ULC-S 109 (large and small scale), IBC Section 803.1.1 (Class A Rating), CAN/CGSB 2-4.162-M80. Bacterial and fungal resistance: ASTM E 2180 and ASTM G21. Environmental certification: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. Safe use: RoHS/Directive 2002/95/EC, US Consumer Product Safety Commission Section 101 and ANSI/WCMA A 100.1-2007 for lead content. Opaque, .016 inches thick, 12.14 oz/square yard.

3.A.8.SheerWeave® Series SW7600 by Phifer®: PVC-free polyester with an acrylic foamed backing. Fire rating: California U.S. Title 19 (small scale), NFPA 701 TM#1 (small scale), BS 5867 Part 2 Type B Performance, CAN/ULC-S 109 (large and small scale). Bacterial and fungal resistance: ASTM G21-96, AATCC 174-1998 Part II and III. Environmental certification: Certified to GREENGUARD® and GREENGUARD Gold® standards for low chemical emissions into indoor air during product usage. Safe use: RoHS/Directive 2002/95/EC, ANSI/WCMA A 100.1-2007 for lead content, US Consumer Product Safety Commission Section 101. UV protection: Seal of approval by the Melanoma International Foundation (MIF) for effectiveness in preventing sun damage to the skin or eyes. Opaque, .020 inches thick, 11.8 oz/square yard.

3.B.Color and pattern: __________, No. _____.

3.C.Color and pattern: As indicated in Color Schedule on Drawings.

3.D.Color and pattern: As selected by Architect from manufacturer’s standard range.

PART 3 EXECUTION

3.1EXAMINATION

1.A.Do not begin installation until substrates have been properly prepared.

1.B.If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2PREPARATION

2.A.Coordinate requirements for blocking and structural supports to ensure adequate means for installation of window shades.

2.B.Coordinate requirements for blocking, construction of shade pockets, and structural supports to ensure adequate means for installation of window shades.

2.C.Coordinate installation of recessed shade pockets with construction of suspended acoustical panel ceilings specified in Section 09510.

2.D.Coordinate installation of recessed shade pockets with construction of suspended gypsum board ceilings specified in Section 09260.

2.E.Coordinate requirements for power supply conduit, and wiring required for window shade motors and controls.

3.3INSTALLATION

3.A.Install in accordance with manufacturer’s instructions.

3.B.Install roller shades level, plumb, square, and true. Allow proper clearances for window operation hardware.

3.C.Shade pockets:

3.C.1.Install shade pockets prior to installation of suspended ceiling system. Attach to supporting structure with screws through top of pocket at 24 inches (610 mm) minimum centers.

3.C.2.Install shade pockets in conjunction with installation of suspended ceiling system. Attach to supporting structure with screws through top of pocket at 24 inches (610 mm) minimum centers.

3.C.3.Install corner pieces securely and in alignment with pockets.

3.C.4.Install pocket ends securely and in alignment with pockets.

3.C.5.After interior construction is essentially complete, install shade and operating mechanism in pocket.

3.D.Install the following items to conceal roller and operating mechanism. Do not use exposed fasteners.

3.D.1.Fascias.

3.D.2.Closure panels.

3.D.3.Endcaps.

3.E.Position shades level, plumb, and at proper height relative to adjacent construction. Secure with fasteners recommended by manufacturer.

3.4TESTING AND DEMONSTRATION

4.A.Test motorized window shades to verify that controls, limit switches, interface to other building systems, and other operating components are functional. Correct deficiencies.

4.B.Demonstrate operation of shades to Owner’s designated representatives.

3.5PROTECTION

5.A.Protect installed products until completion of project.

5.B.Touch-up, repair or replace damaged products before Substantial Completion.

3.6SCHEDULES

6.A.Refer to Drawings for shade types and locations.